Wilton vise parts. Wilton Power Tool Parts

About Me

wilton vise parts

Ball bearings are used to reduce friction between rotating parts. Parker Collars like their jaws have to be custom fit. It is a very old Swivel jaw and swivel base vise since it had the swivel release from under the bench. I want to share the steps I use for building handles. I knew I was going to make new jaws and recut the 3 degree taper after fitting the jaws.

Nächster

Wilton Power Tool Parts

wilton vise parts

I make these myself since I can not find a supplier that carries the ones I like. Use a magnet to remove the chips, air is not enough. I swept in the base diameter with my indicator and with careful numbers that I saved from the inspection I then new how far in the dovetail is and was impressed by seeing how centered the dovetail was. I can get about a dozen jaws cut before re-sharpening. I do not use oil on the tap, you do not want to add any contaminates before welding or brazing. The secret is Rigidity of Setup.

Nächster

About Me

wilton vise parts

Each knob is drilled and reamed for a precision hole and the fixture is machined and threaded for a flat head cap screw. The heat Treater did a nice job on the Heat draw back color. I am a jaw builder so I had plenty of jaw choices, sometimes I have to build a custom jaw but I try to fit a set of Wilton jaws since they are still available to purchase. If you want to eliminate backlash then you will either shorten the two ears and adjust the casting for a close gap between the collar and spindle lip or add Stainless Steel shims or a rather thick one like this one below. The collar has two radial bosses that form the major diameter of the collar and rest and wrap around the Spindle lip.

Nächster

About Me

wilton vise parts

Communicating back and forth with a customer is so important. There are a couple ways of doing it. Not really a big deal unless you like little backlash. Then I find the jaw shoulder with a edge finder and move to the center of the jaw screw hole. My first issue was how the heck do you measure them. The tool pressure will be noticeable when you reach cast material.

Nächster

Wilton Power Tool Parts

wilton vise parts

I would spot one hole then drill and tap then add a screw in the first hole and do the other side. What I mean is the vise has to be tied down tight and the Dynamic shimmed equally on three sides using feeler gages top and both sides and the Dynamic tightened on a spacer block right under the jaw towers. I also rest the finished handle on a piece of delrin, nylon or aluminum to save the finished knob from being damaged. I like to weld since I have several different rod choices to use even though I feel brazing is as good or even better. I also set the end mill to the top of the pin and that would be my Z-zero. It is supplied directly from original equipment manufacturer and it is sold individually. The hard material must be removed so drilling and tapping holes is easier and you are not drilling into hard material.

Nächster

About Me

wilton vise parts

The swivel jaw repair was not easy either till I figured out a way to hold the swivel jaw. Next step is pinching the tail down to bury a Socket Head Cap Screw. If you do bend this stuff, then you are using way too much pressure on your vise. I have found it is easier to cut steps in the ball before sanding the ball smooth. I have machines that cut the two steps evenly but if you do not have access to a milling machine then it has to be done with angle grinders and files. This dimension is listed in the description as center of hole to shoulder and the dimension I list is the maximum your vise can be. All sorts of welding rods can be used, I have Inconel, Nickle, Silicon Bronze and Eutectic 224 Tig rod.

Nächster

About Me

wilton vise parts

It is easy to leave out critical details on the phone or in emails, which kills a lot of time on both ends. On the drawing I list the width of the top part of the Collar where it bolts up to the vise. This is pretty much how I build handles. Fixturing for the straight serrations used on Yost and Starrett jaws should be a little more accurate. On this drawing of a Starrett 326 Pipe Jaw, I added small circles at every intersection where it is easy to connect the dots. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Reed 207 Static Reed 207 Dynamic This method works for me.

Nächster

Wilton Bullet Vise Parts

wilton vise parts

. Brass and Silver Solder works too. You can see the difference in a molded set and cut serrations. Note the hard material showing up when getting close to cast material, I added a pic. Heat is a good way to clean the crack. The reason I find center of the opening is that I cut the jaw side depth to the same numbers so the same thickness jaws will look even when installed.

Nächster